TRGA
reduced viscosity of crude oil and high viscosity petroleum
products.
device and technology.
0. Main theses
:
We
can make devices and systems for reducing the viscosity of heavy
natural oil and other highly viscous products.
We can also solve two important related tasks -1.
Reduce the amount of solvent that is added to
natural oil to reduce its viscosity (see clause 7).
2. Reduce the amount of sediment that forms during
the operation of transit oil tanks for collecting and transporting
heavy oil.
1. Introduction.
-
The topic of crude oil reducing viscosity is
extremely relevant for countries that produce heavy oil. Viscous oil is a problem during production (1), with
temporary storage in transit tanks (2) and in transit pipes
(3).
- the topic
is of great practical importance and any, and even partial,
improvement of current technological processes - will bring
a huge income.
- many
scammers have earned on this topic and a lot of gullible investors
have been ruined, a lot of people talk about it, but we will show you our effects to deserve your attention.
-
Is it possible to reduce the viscosity of crude oil (or other
heavy oil products) using the hardware method, without using
additives or thinners or minimizing their amount? The answer
is yes!
2. Methods solutions.
To reduce
the viscosity of natural oil, viscous petroleum products and
/ or high-molecular substances, there are only four standard
ways:
1.
Increasing the temperature (requires an enormous amount
of energy and its presence or energy infrastructure. In some
cases it is not possible in principle).
2. Mixing with a low viscosity fluid (viscosity averaging)
or with a solvent (viscosity averaging with modification
of the properties of the initial viscous fluid).
3. Mechanical (non-reagent) processing without
the use of additives and solvents.
4. Various combinations of the first three points.
3. Our practical experience.
In the
old days, we had a large number of effects when our TRGA device
reduced the viscosity of fuel oil, oil, high-molecular compounds,
but then it was not our priority task. Recall our pasе
results that you appreciated the reliability of our technical
solution.
1.
Light paraffin oil, Ukraine. Processing on the
module TRGA, before and after processing. At the same
temperature, the viscosity of the treated oil sample (
right ) - considerably lower. Analyzes have not been done.
3.
Ship fuel IFO180, Slovenia, Croatia. year 2012. Processing
on the module TRGA, before and after processing. Analyzes
pivot table.
-
2 weeks after the treatment of ship fuel, the viscosity
was 15% lower than the initial one.
- 3 weeks after the treatment of ship fuel, the viscosity
was less than the initial by 10%.
- lowering the pour point by 2-6 degrees.
- additives and diluents were not used.
4.
Oil sludge open storage, Russia. 2013. Processing
on the module TRGA, before and after processing. At the
same temperature, the viscosity of the treated sledge
sample (right) - considerably lower. Analyzes have not
been done.
The
result is short:
- double reduction of viscosity,, additives and diluents
are not used.
5.
Boiler fuel, fuel oil number 6, (M100) Vladivostok, 2014
and 2012. On the left is the communal
boiler room and the second link
(right) - is the drying
furnace of the asphalt plant.
The
type of fuel is standard M-100 fuel oil (fuel oil number
6 in the American classification).
The
result is short: in both cases, the viscosity
of the treated fuel has decreased so much that it has
become possible to use nozzles with half the flow area.
Additives and thinners were not used.
6.
Oil sludge open long-term storage. Russia, 2016.
Analyzes have not been done. Film.
More.
Film. Left Bank - starting oil with a high
paraffin content, melting point 55 degrees. Bank middle - original oil after processing
with TRGA homogenizer. Right Bank - a standard fuel oil M-100.
(fuel oil number 6 in the American classification)
Air
and fuel oil temperature +20 degrees Celsius.
Time - 5 days after the treatment of fuel oil.
The
result is short:
- 5 days after treatment, without the use of additives
and solvents, the viscosity was less than the initial
two times ... No additives or thinners were used.
This
is an important result for the technology
of mixing natural heavy oil and solvent.
7.
Boiler fuel, fuel oil number 6, Philippines, 2017.Analyzes.
Article.
Boiler fuel of medium viscosity and a mixture of boiler
fuel and 10% diesel fuel.
The
result is short:
- viscosity of low-viscosity boiler fuel, after treatment
without additives and solvents - decreased by
17.48%.
- the viscosity of the mixture (fuel oil + 10% of diesel
fuel as diluent) decreased by 90%.
this
is an important result
for increasing the efficiency of the production of alcohol
8.
High viscosity molasses and comparison of a mixture of
different molasses samples 2017 and 2018. Ukraine.
The result is short:
We
treated mixture
of coarse and fine molasses (viscosity about 2000
centistokes) and this mixture was less viscosity (approximately
twice) than the best of the starting components. Film.
After 6 months, the viscosity of the processed mixture
remained significantly lower than the initial. Link.
Film.
Additives
and solvents were not used.
Below, this film once again, enjoy a
huge difference in viscosity, which was achieved and preserved
6 months after processing the highly viscous product through
a TRGA homogenizer.
And when we put all our results into the system
... we realized that our device and our methods can
be practical use for the task of reducing the viscosity
of petroleum products and other highly viscous substances.
We understood that "we realy can ",
and our equipment is more reliable than others (some samples
work 10 years) and require less energy than other analogues.
9.
We understood that we can and our equipment is more reliable
than the others (up to 10 years trouble-free)
and require less energy less than other analogues.
The result is short: The test in the
certified laboratory GAZPROMNEFT
which has the entire world collection of certificates.
Raw materials - heavy natural oil. The initial viscosity
is 197.8 centipoise. Oil viscosity after a single treatment
(without additives and solvents) - 156 - 159 centipauses.
The same processed samples after 15 days - 165 - 167 centipauses.
The official
report is here.
4. Proposed solution.
The
history of the results and the last test convincingly show that
our equipment can be an important component of devices
and systems for the task of reducing the viscosity of heavy
natural oil and other highly viscous products, including
those prone to sticking. We can also solve two important related
tasks -
1. Reduce
the amount of solvent that is added to natural oil to
reduce its viscosity (see clause 7).
2. Reduce the amount of sediment that forms during
the operation of transit oil tanks for collecting and transporting
heavy oil. Short presentation here.
This is real and reliable information. Want to be our
partner? We
are pleased - this is a good investment. Every year, the viscosity
of the extracted crude oil increases and the cost of its transportation
grows.
